Page 1 of 3

Gookah's Z3 2.8 Progress

Posted: Thu 27 Dec, 2012 19:41
by gookah
Here we go again. ..... Z3 Number 4
This ones my new toy, and to be honest I think all the forthcoming tinkering will be more fun than I got from the fully loaded Z4M I had, 'cos all I could do was polish it and get flashed by other motorists and camera's. :D

This one's a 2.8, and still has enough poke to get me out of shape on occasion... :oops:
Image

Image

Image

Image

The 'M' number plates will go, to be replaced with pressed ones, but they are all I have for now...
So, there's no sport spec, red leather standard seats with no heating... :head: no aircon, and gingercaters all around. But a good base to start with 86,000 on the clock.
A hardtop was included, but the brackets are the homemade version off eBay.
They still work, even though the heated rear window didn't, No cable connections on this version.

Some of you may have seen the first purchase already,
M seats in blue and black, a blue dash, extended leather door cards and extended leather console also in blue leather.
Image

Re: Z3 2.8 Progress Journal

Posted: Thu 27 Dec, 2012 20:00
by Z3cade
Is it the twin or single vanos gookah?

The M seats were the best mod I did to my last 2.8 :)

Re: Z3 2.8 Progress Journal

Posted: Thu 27 Dec, 2012 20:01
by TitanTim
Looking good Pete, look forward to following what you do :lol:

Tim.

Re: Z3 2.8 Progress Journal

Posted: Thu 27 Dec, 2012 20:11
by ('_')Z3
All looks good :D especially with all the bits Santa has brought you this Christmas. Where do you get your pressed plates from?

Re: Z3 2.8 Progress Journal

Posted: Thu 27 Dec, 2012 20:19
by gookah
Z3cade wrote:Is it the twin or single vanos gookah?

The M seats were the best mod I did to my last 2.8 :)

Its an April 2000, so double Vanos M52TU engine, last of the 2.8's

Re: Z3 2.8 Progress Journal

Posted: Thu 27 Dec, 2012 20:21
by gookah
('_')Z3 wrote:All looks good :D especially with all the bits Santa has brought you this Christmas. Where do you get your pressed plates from?

Last set of pressed plates I got from the show at Santa Pod,
however the next set are most likely an internet trawl...TBC

Re: Z3 2.8 Progress Journal

Posted: Thu 27 Dec, 2012 20:23
by gookah
TitanTim wrote:Looking good Pete, look forward to following what you do :lol:

Tim.
Thanks Tim,
I have plenty to do as well......

Image

Santa was extremely generous... :oops:

Re: Z3 2.8 Progress Journal

Posted: Thu 27 Dec, 2012 21:08
by Z3cade
Looks like that lot will keep you busy!!

The M52TU engine is great, and surprisingly economical!
Have you thought about the 330 inlet manifold conversion? It's quite easy DIY job and all you need is the manifold and adaptor bracket.. Bolt on job £150-200 for parts
But best to get it remapped to get best benefits from it if you do..

Look forward to your progress

Re: Z3 2.8 Progress Journal

Posted: Thu 27 Dec, 2012 21:12
by gookah
Z3cade wrote:Have you thought about the 330 inlet manifold conversion?
As if......... :wink:

Re: Z3 2.8 Progress Journal

Posted: Thu 27 Dec, 2012 21:18
by Z3cade
Good man :twisted:

Any plans for wheels?

Re: Z3 2.8 Progress Journal

Posted: Thu 27 Dec, 2012 23:06
by gookah
Z3cade wrote:Good man :twisted:

Any plans for wheels?

yes, indeed

Re: Z3 2.8 Progress Journal

Posted: Fri 28 Dec, 2012 00:00
by gookah
First hurdle to overcome was the recurring engine light and the erratic idle when cold.

and the cause:
Image

the common split elbow. so for less than a tenner I bought part no 13541435627. Please note it is a superseded part and you do not need the extra hose clip or joint that they advise if yours already has the two adjacent hose clips as shown.
Codes showing were P0170 and P0173 fuel banks 1 and 2.
Until I got the new elbow I kept resetting these to turn of the light.
Since changing the elbow they have not returned and the idle is smooth again.

and the dust in that engine bay.... :bawl:

Re: Z3 2.8 Progress Journal

Posted: Fri 28 Dec, 2012 01:00
by gookah
So.... the dash was a tricky job to refit, as the 3 bolts under the windscreen (7mm socket size) screw into spring clips that slide about, and you cant move them with the dash in place if they are slightly out.
But other than that, just took a while to strip everything out.
Image

Image

Image

What do you do with the original red console? The replacement one that I bought had the blue extended leather under the handbrake but was the pre-facelift.... :head:
Anyway, I got some blue carbon vinyl and wrapped my red console and swapped over the switch panels. I also wrapped the steering wheel trim.. but I'm not sure.
It may have to go black carbon.

Image

Image

Image

The seats had different connections for the seatbelt pre-tensioners, so I had to solder the new connectors in place. Luckily I had the foresight to get both male and female halves from the breakers, All other connectors were identical, and I kept the airbag module.
All the other wiring was there for the heated seats and they plugged straight in. I had a couple of facelift heated seat switches given to me by my son G8JKA and the relay was already fitted.
Whilst the console was out I moved the roof switch wiring to the front as well..
Seats fitted, windows greased before fitting the new door cards, airbag light reset, (I had to move the car with the seats out..) and everything tested and working fine.
Lovely having heat on base and back again..... God those old seats were cold in a morning.

They need to have the scuffmaster treatment, but for now will suffice as the colour looks darker than Estoril, but thats is what the doorcards and console have written on them and I need to get the match correct.
Anyway here are a few pics of the new interior..

Image

Image

The head unit is next....

Re: Z3 2.8 Progress Journal

Posted: Fri 28 Dec, 2012 04:55
by Vanne
Hi ya Gookah,


Mate extremely interested in your updated console. I also have a 2k z3 but a coupe, mine has the older style console in it with the larger push button switches. I recently bought a 2001 console (like your new one) but was wondering if the connectors at the back of the switches will be plug and play or will I have to get he soldering iron out?

By the way, nice bunch of mods mate ;)

Re: Z3 2.8 Progress Journal

Posted: Fri 28 Dec, 2012 09:08
by Captain
Looking good, really like the M seats :D

Re: Z3 2.8 Progress Journal

Posted: Fri 28 Dec, 2012 09:39
by Brian H
Great read, this brings back fond memories of me doing something similar to the interior of my last car. It totally transforms the feel of the car :thumb:

Santa was certainly good to you, be interested to hear some feedback on the springs you are going to fit. I see Eibach supply 2 different spring types, sport line and pro-kit. Not sure how much difference there is between the two types?

Look forward to the next update.

Re: Z3 2.8 Progress Journal

Posted: Fri 28 Dec, 2012 12:14
by gookah
Vanne wrote:Hi ya Gookah,


Mate extremely interested in your updated console. I also have a 2k z3 but a coupe, mine has the older style console in it with the larger push button switches. I recently bought a 2001 console (like your new one) but was wondering if the connectors at the back of the switches will be plug and play or will I have to get he soldering iron out?

By the way, nice bunch of mods mate ;)
You will need the different switches also, as pre-facelift switches don't fit the facelift console (they are different widths,) but hopefully they are supplied in your new console, however the connectors are also different for the older/newer switches even though they do the same job, I believe your coupe may have the older style wiring loom and connections

Re: Z3 2.8 Progress Journal

Posted: Fri 28 Dec, 2012 12:34
by gookah
Brian H wrote:Great read, this brings back fond memories of me doing something similar to the interior of my last car. It totally transforms the feel of the car :thumb:

Santa was certainly good to you, be interested to hear some feedback on the springs you are going to fit. I see Eibach supply 2 different spring types, sport line and pro-kit. Not sure how much difference there is between the two types?

Look forward to the next update.

The Sport Line (red springs), IF you can get hold of them, are lower, (as in 45-50mm drop) and firmer and recommended for track cars, The Pro-Kit lower 30mm all round and are more suited for a daily road going car.
I had the Pro-Kit on both my Z4's as well and they improved the looks and handling.

Re: Z3 2.8 Progress Journal

Posted: Fri 28 Dec, 2012 12:43
by g8jka
gookah wrote:Image
Please lose that ///M badge :head: :roflmao:

Have you fitted that stereo yet? :roll:

Re: Z3 2.8 Progress Journal

Posted: Fri 28 Dec, 2012 17:30
by Z3cade
Makes such a differents having the M seats in.. Your interior reminds me so much of my 2.8 :( miss it..

Keep up the good work :)

Re: Z3 2.8 Progress Journal

Posted: Fri 28 Dec, 2012 19:24
by gookah
The head unit and sub are now in, and working a treat, iPhone connected and wiring hidden, Bluetooth handsfree through the speakers with auto mute of the radio, even for directions in maps app.
Head unit controls the iPhone and charges it too.
You can even tailor the colour to the car, The display can be blue/white/green/red and every shade in between. I saw over 30 odd settings, and chose the orange closest to the standard.
Another feature is if the phone rings, the display colour is selectable and the default changes it to flashing blue..
It sounds great with the sub now..

Image

Image

a better pic of the interior, with the hardtop removed..:
Image

and the stainless hoops installed,
Image

These are the homemade hardtop brackets,
Image

Image

I got a facelift HRW switch, and plugged it in, but had to connect into the existing wiring behind the passenger seat. But that works now as well..

also put the seat tilt kit on the drivers (cheapo version)
That will do for today...

Re: Z3 2.8 Progress Journal

Posted: Fri 28 Dec, 2012 19:52
by Del
Gookah – would you mind me asking whether there is a particular type of carbon fibre sheeting you would recommend for the internal dash trimming. I don't know much about it.

Re: Z3 2.8 Progress Journal

Posted: Fri 28 Dec, 2012 20:05
by gookah
Just look on eBay for the 3M stuff, its all pretty similar

Re: Z3 2.8 Progress Journal

Posted: Sun 03 Feb, 2013 20:52
by gookah
Bought some Scuffmaster in Estoril blue:
Image

I also bought a leather repair kit, slid a 'repair patch' underneath the rip, applied the glue, then held it together for 2 mins and left it for an hour.
Cleaned the leather with the cleaner from the repair kit then applied the Scuffmaster by dabbing it on with a sponge.

This was the drivers side, and was after just one coat,

Image Image
I will do another coat tomorrow, then onto the passenger side which is no where near as bad.

a view from afar:
Image
Impressed is not an adequate enough word for how I feel....

Also had a small cigarette burn, and in the repair kit was some leather filler, so applied it and now I will touch up with a marker pen until I get some black Scuffmaster.
Image

Re: Z3 2.8 Progress Journal

Posted: Sun 03 Feb, 2013 21:10
by ('_')Z3
Looking really good :D
My first standard red leather seats I used the German kit (can't quite remember the name :oops: ) and was impressed with that as well, but not cheap!
When I got the ///M seats I decided to get the drivers bolster done professionally which to be honest was the same cost as the German kit and looked even better, £60 I think!
It looks like you've got a great finish though for a first coat

Re: Z3 2.8 Progress Journal

Posted: Sun 03 Feb, 2013 23:38
by Pierrick
Wow!!! The result on the seat is amazing!! Where did you get the scuff master and the repair kit???

There is a few places on the internet where we can found the scuff master but I'm not sure about the repair kit! Your seat looks very good so if I could do the same on my seat I would be more than pleased!!

Re: Z3 2.8 Progress Journal

Posted: Mon 04 Feb, 2013 12:03
by gookah
Pierrick wrote:Wow!!! The result on the seat is amazing!! Where did you get the scuff master and the repair kit???

There is a few places on the internet where we can found the scuff master but I'm not sure about the repair kit! Your seat looks very good so if I could do the same on my seat I would be more than pleased!!
This is the repair kit,:
http://www.ebay.co.uk/itm/130567872335? ... 1497.l2649


and Scuffmaster is available here :
http://www.liquidleather.com/scuffs.htm

Re: Gookah's Z3 2.8 Progress

Posted: Mon 04 Feb, 2013 12:35
by Z3cade
Looking good Gookah.. Keep up the good work!

Re: Gookah's Z3 2.8 Progress

Posted: Mon 04 Feb, 2013 19:03
by gookah
Also tried to get rid of some of the sagginess in the leather with a hot air gun,
Image


this was as much as I dared...
Image

Passenger side now in progress....
Image

Re: Gookah's Z3 2.8 Progress

Posted: Mon 04 Feb, 2013 19:11
by Pierrick
Ok thanks. There is a lot in this repair kit! Did you use everything?

I found a very cheap one, I guess you have the same in yours plus other bits...
http://www.ebay.co.uk/itm/Leather-Repai ... 4ab37b142a

And for the colour I found this:
http://www.ebay.co.uk/itm/Scuff-Master- ... 27ce888e24
Which i think is the same as yours but red... i'm just not sure if this the right red for me!

Or this one:
http://www.ebay.co.uk/itm/33-33-100ml-c ... 19d2e2656a
Which seems to be the right colour. (Q2TD Tanin red)

Thanks for your help, i might create a mew post at the right place to not pollute tis one!

Re: Gookah's Z3 2.8 Progress

Posted: Mon 04 Feb, 2013 19:40
by Brian H
Great job with the seats, they look to be coming up a real treat. Jobs like these are so satisfying when the results can easily be seen. I would not have thought of a heat gun to tighten the seats :thumb:

Re: Gookah's Z3 2.8 Progress

Posted: Wed 06 Feb, 2013 14:19
by Evs87
Gookah,

Where did you get that iphone mount? Does is come with the usb cable attatched? Would you recommend that stereo for use with iPhones?

Re: Gookah's Z3 2.8 Progress

Posted: Wed 06 Feb, 2013 15:30
by gookah
Evs87 wrote:Gookah,

Where did you get that iphone mount? Does is come with the usb cable attatched? Would you recommend that stereo for use with iPhones?
EBay:
http://www.ebay.co.uk/itm/Dexim-DCA166- ... 416eb939b7
It has a USB cable attached and this plugs into the back of the head unit to charge/ play music.

The head unit works equally well as a direct usb connection, or bluetooth streaming of the music.
On longer journeys I put the phone in the dock to also charge it, but on short ones I just use the streaming as it sees the phone when I start the car.

Re: Gookah's Z3 2.8 Progress

Posted: Sun 31 Mar, 2013 20:47
by gookah
Decided to apply the Scuffmaster to the centre console carbon wrap, ~It matches better than the previous blue and gives it a matt finish.

Image

Image


Also fitted my new illuminated start button:

Image

Image

Pointless gadget I know, but simple things..... :D

Re: Gookah's Z3 2.8 Progress

Posted: Sun 31 Mar, 2013 20:51
by gookah
Also had a new roof fitted yesterday, and as the interior was now blue, I decided to copy G8JKA and get a blue one as well:

Image

Re: Gookah's Z3 2.8 Progress

Posted: Sun 31 Mar, 2013 21:30
by Z3cade
Looks fantastic pete 8-) Love the blue soft top on silver contrast.. Best colour combo on silver imo

Re: Gookah's Z3 2.8 Progress

Posted: Mon 01 Apr, 2013 06:10
by Southernboy
:thumb: LIKE IT !

Re: Gookah's Z3 2.8 Progress

Posted: Mon 01 Apr, 2013 07:10
by Badman gee
Turn them to face each other it will look like a mirror

Re: Gookah's Z3 2.8 Progress

Posted: Mon 01 Apr, 2013 08:11
by Captain
Looking good, also really like the colour combo.

Sent from my HTC Desire

Re: Gookah's Z3 2.8 Progress

Posted: Mon 01 Apr, 2013 11:40
by PCSAM
can you please stop doing these things to your car :evil: :head: . just when i think i have my car the way i like it . you come along every time with stuff that looks great and suits the car well :head:
now i want more bits i cant afford ..









:D looks great mate , love the hood colour 8-) 8-)

Re: Gookah's Z3 2.8 Progress

Posted: Mon 01 Apr, 2013 17:26
by gookah
PCSAM wrote:can you please stop doing these things to your car
Just wait 'til I post the other stuff I still have to do......

Sorry :oops:

Re: Gookah's Z3 2.8 Progress

Posted: Sun 14 Apr, 2013 10:48
by gookah
new handbrake handle to match my shiny knob:

Image

Re: Gookah's Z3 2.8 Progress

Posted: Sun 14 Apr, 2013 13:26
by Captain
Is that the storm handbrake handle. Looks good.

Sent from my GT-I8190 using Tapatalk 2

Re: Gookah's Z3 2.8 Progress

Posted: Sun 14 Apr, 2013 14:02
by Badman gee
Captain wrote:Is that the storm handbrake handle. Looks good.

Sent from my GT-I8190 using Tapatalk 2
Not storm motorwerks.

Re: Gookah's Z3 2.8 Progress

Posted: Sun 14 Apr, 2013 21:16
by gookah
Finalised the pager alarm with remote engine start:

Re: Gookah's Z3 2.8 Progress

Posted: Sun 14 Apr, 2013 21:22
by gookah
And a remote roof close, which will work from in the house, or up to 100 metres away,




OK it doesn't latch the handles, but if it starts chucking it down, I can remotely shut the roof, while I get my coat.
I just have to get in and clamp up, but now there is no sitting in the rain going through the motions getting soaked..
.....
And I just wanted to see if it could be done. :D

Re: Gookah's Z3 2.8 Progress

Posted: Sun 14 Apr, 2013 21:37
by Z3cade
Some great mods there Pete! Well done :wink:

Re: Gookah's Z3 2.8 Progress

Posted: Sun 14 Apr, 2013 21:41
by gookah
and lowered today with new Eibachs and front Boge struts.
and a new strut brace:
Image

What a difference in driving....
Next week I might get the summer alloys out..... :D

Re: Gookah's Z3 2.8 Progress

Posted: Sun 14 Apr, 2013 21:44
by gookah
and while were at it, I might as well show the induction kit with hose routed through to front bumper lower grille:

Image

Re: Gookah's Z3 2.8 Progress

Posted: Sun 14 Apr, 2013 22:29
by Bi11
Blimey, you've had a busy weekend. Looks smart.